EarthQuaker Devices Avalanche Run (Stereo Delay & Reverb) V2$299.00
Avalanche Run Stereo Reverb & Delay The Avalanche Run was developed with one goal in mind: to take the floating ambient tones of our Dispatch Master to the next level while still keeping it user friendly and refined. Taking you into...- Read More
SOLD. This item is currently on backorder.
Stereo Reverb & DelayThe Avalanche Run was developed with one goal in mind: to take the floating ambient tones of our Dispatch Master to the next level while still keeping it user friendly and refined. Taking you into the aural exploratorium without having to break open the user manual every time you want to open up your inner eye and get free is no easy task. We are using a high powered proprietary DSP platform to recreate all the characteristics of all our old favorite delay and reverb machines while still retaining a simple, yet flexible workspace. It has been a long time coming but well worth the wait! Enough, let’s talk about the damn pedal!
The Tap switch also has a few other cool secondary functions. While in Normal and Swell mode, you can send the Avalanche Run into self-oscillation by holding down the “Tap” footswitch. In Reverse, mode holding down the Tap switch will flip the delay back into Normal mode and return to Reverse mode once released!
Each and every Avalanche Run is completely assembled, wired and tested by total human beans in the tiny tundra town of Akron, Ohio.
Time: This controls the delay time and goes from 0ms to just under 2000ms.
Repeats: Controls the regeneration of the delay, from zero repeats to near infinite.
Tone: Controls the tone for the delay line only. Roll off highs to the left, roll off lows to the right and get a flat response in the middle.
Mix: The is the volume control for the delay line. This blends in the wet with dry until 1 o’clock, 1 o’clock to 3 o’clock boosts the wet signal over the dry and 3 o’clock up brings down dry until it is fully wet when all the way up.
Expression Jack Assign Switch: Use this switch to map the expression jack to one of the assigned controls.
• Decay- Controls the reverb decay length
• R Mix- Controls the reverb mix
• Time- This takes over for the delay time control and is DRASTICALLY different than the interface control. Using the expression pedal to control the time will give you all kinds of wild effects that can not be achieved by turning the knob.
• Repeats- Controls the delay repeats
• D Mix- Controls the delay mix
• Toggle- This takes over for the toggle switch and will cross fade from forward delay in heel down position to reversedelay in toe down position.
Decay: Controls the decay length of the reverb, short decay counterclockwise, long cavernous decay clockwise.
Mix: This is the volume control for the reverb. Blends in the wet with dry until 1 O’clock, 1 O’clock to 3 O’clock boosts the wet signal over the dry and 3 O’clock up brings down dry until it is fully wet when all the way up.
Ratio Selector Switch: Selects delay subdivisions when time is set by the “Tap” switch.
• 1/1- Quarter Note
• 3/4- Dotted 8th
• 2/3- Quarter Note Triplet
• 1/2- 8th Note
• 1/3- 8th Note Triplet
• 1/4- 16th Note
TOGGLE SWITCH (MODE SELECTOR)
Both: This is the “standard” delay and reverb mode
Reverse: This is reverse delay mode with “standard” reverb
Swell: This is the volume swell mode
4.625″ x 3.7″ x 2.25″ with knobs
Our pedals take a standard 9-volt DC power supply with a 2.1mm negative center barrel. We always recommend pedal-specific, transformer-isolated wall-wart power supplies or multiple isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power. Switching-type power supplies, daisy chains and non-pedal specific power supplies do not filter dirty power as well and let through unwanted noise. Do not run at higher voltages!
Current draw is 425 mA.
This device is true bypass and uses electronic relay based switching. Audio will not pass without power.
For standard latching operation, tap the footswitch once to activate the effect and then tap again to bypass. For momentary operation, hold the footswitch down for as long as you’d like to use the effect. Once you release the switch the effect will be bypassed.
V2 Updates - January 2018
• New flexi switch silent relay based switching allows for traditional latching or momentary operation
• Updated reverb algorithm for improved stereo imaging
• New custom-built enclosure
Stereo Reverb and Delay with Tap Tempo
Do you need help with something? Click here to speak with a live support agent.
What type of payments do you accept?
We accept payments from MasterCard, Visa, Discover, American Express and PayPal. You can read about our financing options here.
What is your shipping policy?
We will ship completed orders Monday-Friday. Orders placed and paid before 1:00pm. PST will ship that same day. All completed orders after the cutoff time will ship the following business day. RGS does not ship on Saturday or Sunday.
What is your return policy?
We offer a 30 day Exchange policy for new purchases. We ask that you please return the product in the original product packaging along with all included materials (manual, warranty card, all accessories) and in the original condition that it was received and we will exchange it for any product on ours site. Please note that we do charge a $5 dollar exchange fee to cover our shipping cost. We are a small business and do not offer a cash refund. We cannot take returns on sealed product. We do not accept returns for guitars and amplifiers under any circumstances. Unfortunately we also cannot cancel orders or pre-orders. We are happy to exchange for another product if you are no longer interested in the new release or backordered items